On Sunday afternoon, a group of ladies and I got together for a DIY Deco Mesh Wreath Party. We had SO much fun and this wreath was much easier to make than I expected. My mind came alive with so many wreath possibilities -
- Holidays/Seasonal
- Disney Themed
- Front door address (with numbers)
- How about a wreath showcasing your marathon accomplishments? Hey, it could be done!
I’m going to show you a few images from our party followed by a step by step photo tutorial.
I decided I wanted to make a Valentines Day wreath. My current wreath was sadly faded and I was in need of something new! I pinterested a few ideas, then hunted through Hobby Lobby for my supplies.
Several ladies gathered for the party with lots of different ideas.
Our wreaths ranged from Mardi Gras, Spring, 4th of July, and even one that included house numbers for a front door (and it was burlap, too)! I wish I had a picture of it, but I don’t – it was a super cute idea!
After finishing with the deco mesh, I applied ribbon. Tip: Don’t wrap the ribbon all the way around. Measure your loops and cut your ribbon. It wastes ribbon if you continuously loop it around your wreath.
Co-workers with their finished Mardi Gras and 4th of July wreaths.
Valentines Day wreath complete!
Here’s the supplies you’ll need:
- 16” wreath form with tinsel ties
(not plain green wire form; this will be wire form with tinsel tree like branches on it) - 2 rolls of deco mesh (the big rolls, not the small ones); these could be the same color or different colors, doesn’t matter
- Pipe Cleaners
- Wired Ribbon (if you choose to add this)
- Light weighing décor that can be hot glued to the mesh
All of my supplies were purchased at Hobby Lobby with the exception of the heart ribbon which came from Michaels.
Source
Your wreath form will have two layers – point the wire pieces up towards you.
Roll out your mesh
Grab the starting end of your garland and bunch it together. Then, fold the end down to form a “pony tail”. The area where my fist is located is the area that will begin the wreath on the frame.
Find a starting location on the outer ring – doesn’t matter where. Double twist the garland/twist tie/wire around the “pony tail” and twist it tight!
Now the fun begins!
Measure out about 12 inches, then secure again on the OUTER ring. You can make it a little smaller than 12 inches for a less “poofier” wreath. Double twist each twist tie – also make these tight.
I used about 8 inches here. My completed wreath from the party was about 12 inches.
Continue looping your mesh around the outside edge of the wreath form.
When you reach your starting location, secure your current end to the same twist tie/wire where your beginning loop is located.
If you have a second color, secure a pony tail loop to the same twist tie you used previously for your starting location. It might look like you are running out of room with your wire, don’t panic, that’s why you have extra twist ties!
If using the same color, carry on with the next step as described. If you run out of one roll, begin the new roll where you left off.
Now you are going to begin an in-out pattern with your mesh.
Instead of following around on the outside loop, use the closest wire/garland tie on the inside loop. Secure, then bring your mesh up to the next outside garland/wire tie and secure over the mesh already there. Bring your mesh back to the next inside garland/wire, then again to the next outside wire. Continue this pattern until you reach your starting location. By the end, all of your inside loops will include mesh and your outside loops will have been used twice.
Your second roll WILL overlap with your first roll and that’s ok, that’s what you want!
After completing an entire round of pink and an entire round of white, I decided my wreath didn’t include enough pink, so I went back in and added another layer of pink to the inside loops. The options are limitless!
When ready to add your ribbon, don’t loop ribbon all the way around your wreath. Measure out your loops, then secure ends with the garland/wire ties. You’ll waste ribbon otherwise.
You can see on the back of mine, I didn’t loop anything around.
Hot glue embellishments throughout your wreath.
Hang and enjoy! Again, the options are endless.
I created a board on Pinterest especially for Deco Mesh wreaths. Check it out, you might find something that inspires you!
I’m thinking a Disney wreath might be next…or possibly a race inspired wreath – I’m going to have to think about it a bit more. I’m afraid I’ve created a monster…uhoh.
Have you ever made a Deco Mesh wreath? How about any DIY projects off Pinterest?
![NSYNCValentine_thumb[1]](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEjFp0IfYRUKOLYAIcc7SbvSom3jXbBANSVaPuq6KAlkOFm9Mt3ub6AqHw9BoJc3BnIRD0ty4nZaSG_q-eZZ6wOCKyqfetZRAp_ldMzawA-uFqhQIQ0CrK37bThNtlJraPEEc0l-6zDRd499/?imgmax=800 "NSYNCValentine_thumb[1]")
